PHY сбрасывается через каждые несколько секунд. Несмотря на строку PHY: 0:00 - Link is Up - 100/Full связи все равно нет.
PowerPrep start initialize power... Battery Voltage = 1.95V No battery or bad battery detected!!!.Disabling battery voltage measurements./r/nMay 22 201808:18:22 FRAC 0x92925552 memory type is DDR2 Wait for ddr ready 1power 0x00820710 Frac 0x92925552 start change cpu freq hbus 0x00000003 cpu 0x00010001
U-Boot 2009.08 (Sep 18 2015 - 11:31:04)
Freescale i.MX28 family CPU: 454 MHz BUS: 151 MHz EMI: 205 MHz GPMI: 24 MHz DRAM: 128 MB MMC: IMX_SSP_MMC: 0, IMX_SSP_MMC: 1 In: serial Out: serial Err: serial Net: got MAC address from IIM: 00:04:70:b3:d5:08 FEC0 Hit any key to stop autoboot: 0
MMC read: dev # 0, block # 256,count 12288 ... 12288 blocks read: OK ## Booting kernel from Legacy Image at 42000000 ... Image Name: Linux-2.6.35.3-zeo-tion-pro28 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2995784 Bytes = 2.9 MB Load Address: 40008000 Entry Point: 40008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel. Linux version 2.6.35.3-zeo-tion-pro28 (ubuntu@ubuntu) (gcc version 4.4.4 (4.4.4_09.06.2010) ) #77 PREEMPT Fri Aug 17 11:20:11 EDT 2018 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: Freescale MX28EVK board Memory policy: ECC disabled, Data cache writeback Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttyAM0,115200n8 noinitrd root=/dev/mmcblk0p3 rw rootwait PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 128MB = 128MB total Memory: 123268k/123268k available, 7804k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xfde00000 - 0xffe00000 ( 32 MB) vmalloc : 0xc8800000 - 0xf0000000 ( 632 MB) lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .init : 0xc0008000 - 0xc007f000 ( 476 kB) .text : 0xc007f000 - 0xc05f3000 (5584 kB) .data : 0xc05f4000 - 0xc0637480 ( 270 kB) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. RCU-based detection of stalled CPUs is disabled. Verbose stalled-CPUs detection is disabled. NR_IRQS:288 Console: colour dummy device 80x30 console [ttyAM0] enabled Calibrating delay loop... 226.09 BogoMIPS (lpj=1130496) pid_max: default: 32768 minimum: 301 Security Framework initialized SELinux: Initializing. Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok regulator: core version 0.5 NET: Registered protocol family 16 regulator: vddd: 800 <--> 1575 mV at 1500 mV fast normal regulator: vdddbo: 800 <--> 1575 mV fast normal regulator: vdda: 1500 <--> 2275 mV at 1800 mV fast normal vddio = 3280000, val=10 regulator: vddio: 2780 <--> 3680 mV at 3280 mV fast normal regulator: overall_current: fast normal regulator: vbus5v: regulator: mxs-duart-1: fast normal regulator: mxs-bl-1: fast normal regulator: mxs-i2c-1: fast normal regulator: mmc_ssp-1: fast normal regulator: mmc_ssp-2: fast normal regulator: charger-1: fast normal regulator: power-test-1: fast normal regulator: cpufreq-1: fast normal i.MX IRAM pool: 120 KB@0xc8820000 Initializing GPMI pins usb DR wakeup device is registered IMX usb wakeup probe audit: cannot initialize inotify handle bio: create slab <bio-0> at 0 SCSI subsystem initialized Freescale USB OTG Driver loaded, $Revision: 1.55 $ usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Switching to clocksource mxs clock source NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Bus freq driver module loaded IMX usb wakeup probe usb h1 wakeup device is registered mxs_cpu_init: cpufreq init finished audit: initializing netlink socket (disabled) type=2000 audit(0.600:1): initialized VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) JFFS2 version 2.2. (NAND) A© 2001-2006 Red Hat, Inc. msgmni has been set to 240 alg: No test for stdrng (krng) cryptodev: driver loaded. Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) Console: switching to colour frame buffer device 80x60 mxs-duart.0: ttyAM0 at MMIO 0x80074000 (irq = 47) is a DebugUART UART set mode; UART - 0, mode - 0
mxs-auart.0: ttySP0 at MMIO 0x8006a000 (irq = 112) is a mxs-auart.0 Found APPUART 3.1.0 (DMA) UART set mode; UART - 1, mode - 0
mxs-auart.1: ttySP1 at MMIO 0x8006c000 (irq = 113) is a mxs-auart.1 Found APPUART 3.1.0 (DMA) UART set mode; UART - 2, mode - 0
mxs-auart.2: ttySP2 at MMIO 0x8006e000 (irq = 114) is a mxs-auart.2 Found APPUART 3.1.0 (DMA) UART set mode; UART - 3, mode - 0
mxs-auart.3: ttySP3 at MMIO 0x80070000 (irq = 115) is a mxs-auart.3 Found APPUART 3.1.0 (DMA) UART set mode; UART - 4, mode - 0
mxs-auart.4: ttySP4 at MMIO 0x80072000 (irq = 116) is a mxs-auart.4 Found APPUART 3.1.0 (DMA) brd: module loaded loop: module loaded i.MX GPMI NFC NFC: Version 1, 8-chip GPMI and BCH Boot ROM: Version 1, Single-chip boot area, block mark swapping supported Scanning for NAND Flash chips... NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit) Scanning device for bad blocks Bad eraseblock 1 at 0x000000020000 Bad eraseblock 2 at 0x000000040000 Bad eraseblock 3 at 0x000000060000 Boot area protection is enabled. Creating 2 MTD partitions on "gpmi-nfc-main": 0x000000000000-0x000001400000 : "gpmi-nfc-0-boot" 0x000001400000-0x000010000000 : "gpmi-nfc-general-use" mxs-spi mxs-spi.0: Max possible speed 24000 = 24000000/2 kHz mxs-spi mxs-spi.0: at 0x80014000 mapped to 0xF0014000, irq=84, bus 1, DMA ver_major 4 Freescale FlexCAN Driver FEC Ethernet Driver fec_enet_mii_bus: probed ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver fsl-ehci fsl-ehci: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci: new USB bus registered, assigned bus number 1 fsl-ehci fsl-ehci: irq 93, io base 0x80080000 fsl-ehci fsl-ehci: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: Freescale On-Chip EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.35.3-zeo-tion-pro28 ehci_hcd usb usb1: SerialNumber: fsl-ehci hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 2 fsl-ehci fsl-ehci.0: irq 92, io base 0x80090000 fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00 usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: Freescale On-Chip EHCI Host Controller usb usb2: Manufacturer: Linux 2.6.35.3-zeo-tion-pro28 ehci_hcd usb usb2: SerialNumber: fsl-ehci.0 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. ARC USBOTG Device Controller driver (1 August 2005) mice: PS/2 mouse device common for all mice input: MXS touchscreen as /devices/virtual/input/input0 rtc-ds1307 0-0068: rtc core: registered m41t00 as rtc0 i2c /dev entries driver IR NEC protocol handler initialized IR RC5(x) protocol handler initialized IR RC6 protocol handler initialized IR JVC protocol handler initialized IR Sony protocol handler initialized Linux video capture interface: v2.00 WARNING : No battery connected !
Aborting power driver initialization mxs-battery: probe of mxs-battery.0 failed with error 1 mxs watchdog: initialized, heartbeat 19 sec mxs-mmc: MXS SSP Controller MMC Interface driver mxs-mmc mxs-mmc.0: mmc0: MXS SSP MMC DMAIRQ 82 ERRIRQ 96 dcp dcp.0: DCP crypto enabled.! usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid usbhid: USB HID core driver Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (1926 buckets, 7704 max) CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or sysctl net.netfilter.nf_conntrack_acct=1 to enable it. ctnetlink v0.93: registering with nfnetlink. xt_time: kernel timezone is -0000 ip_tables: (C) 2000-2006 Netfilter Core Team ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully arp_tables: (C) 2002 David S. Miller TCP cubic registered NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team IPv6 over IPv4 tunneling driver mmc0: new high speed SDHC card at address 0007 mmcblk0: mmc0:0007 SD16G 14.4 GiB mmcblk0: NET: Registered protocol family 17 Bridge firewalling registered Ebtables v2.0 registered can: controller area network core (rev 20090105 abi 8) NET: Registered protocol family 29 p1 p2 p3 regulator_init_complete: incomplete constraints, leaving vbus5v on rtc-ds1307 0-0068: setting system clock to 2018-09-04 11:40:11 UTC (1536061211) EXT2-fs (mmcblk0p3): warning: mounting unchecked fs, running e2fsck is recommended VFS: Mounted root (ext2 filesystem) on device 179:3. Freeing init memory: 476K
init started: BusyBox v1.15.0 ()
starting pid 759, tty '': '/etc/rc.d/rcS' Mounting /proc and /sys Running sysctl Setting up networking on loopback device: Setting up networking on eth0: eth0: Freescale FEC PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=0:00, irq=-1) Adding static route for default gateway to 192.168.1.1: Setting nameserver to 192.168.1.1 in /etc/resolv.conf: Starting inetd: Starting the hotplug events dispatcher udevd Synthesizing initial hotplug events PHY: 0:00 - Link is Up - 100/Full Setting the hostname to freescale Mounting filesystems Resetting PHY EXT2-fs (mmcblk0p3): error: ext2_lookup: deleted inode referenced: 29075 EXT2-fs (mmcblk0p3): error: ext2_lookup: deleted inode referenced: 29075 EXT2-fs (mmcblk0p3): error: ext2_lookup: deleted inode referenced: 29075 ln: /etc/mtab: Input/output error EXT2-fs (mmcblk0p3): error: ext2_lookup: deleted inode referenced: 29075 EXT2-fs (mmcblk0p3): error: ext2_lookup: deleted inode referenced: 29075 mount: can't open /etc/mtab for writing: Input/output error Starting the port mapper: Starting the ssh server: Starting the watchdog daemon: EXT2-fs (mmcblk0p3): error: ext2_free_blocks: bit already cleared for block 217088 sh: start: unknown operand
starting pid 1333, tty '': '/sbin/getty -L ttyAM0 115200 vt100'
arm-none-linux-gnueabi-gcc (4.4.4_09.06.2010) 4.4.4
root filesystem built on Fri, 02 Oct 2015 12:16:03 -0400
Freescale Semiconductor, Inc.
freescale login: Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY Resetting PHY PHY: 0:00 - Link is Down PHY: 0:00 - Link is Up - 100/Full Resetting PHY PHY: 0:00 - Link is Up - 100/Full Resetting PHY PHY: 0:00 - Link is Up - 100/Full Resetting PHY Resetting PHY Resetting PHY Resetting PHY
arm-none-linux-gnueabi-gcc (4.4.4_09.06.2010) 4.4.4
root filesystem built on Fri, 02 Oct 2015 12:16:03 -0400
Freescale Semiconductor, Inc.
freescale login: root login[1333]: root login on 'ttyAM0'
BusyBox v1.15.0 () built-in shell (ash) Enter 'help' for a list of built-in commands.
root@freescale ~$ ls SP1 minicom.log root@freescale ~$ Resetting PHY mc -sh: mc: not found root@freescale ~$ ifcResetting PHY onfig eth0 Link encap:Ethernet HWaddr 70:B3:D5:08:32:98 inet addr:192.168.1.28 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:468 (468.0 b) Base address:0x8000
lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
root@freescale ~$ Resetting PHY Resetting PHY PHY: 0:00 - Link is Down PHY: 0:00 - Link is Up - 100/Full
|