ЗАО «ЗЭО»
Техническая поддержка пользователей => Тион-Про28, Орион28 => Тема начата: Александр Глухов от 15 Октября, 2014, 08:14:44
-
Здравствуйте, у меня следующая проблема. Я запускаю с консоли com-порта программу и получаю изображение, которое вижу на экране монитора через VGA, но на тачскрине черный экран.
вводил export
DISPLAY=:0
TSLIB_TSDEVICE=/dev/input/ts0
ts_calibrate запускается, но нет никаких маркеров, вижу, что считывает нажатия. Так же вижу через экран монитора курсор, который бегает, когда трогаю тач (правда он теперь неверно откалиброван, из-за того, что не было маркеров).
То же самое с пингвином при загрузке - на VGA есть, на таче нет.
Также выдает реакцию на нажатия evtest:
evtest /dev/input/ts0
Input driver version is 1.0.0
Input device ID: bus 0x0 vendor 0x0 product 0x0 version 0x0
Input device name: "MXS touchscreen"
Supported events:
Event type 0 (Sync)
Event type 3 (Absolute)
Event code 0 (X)
Value 1758
Min 0
Max 4095
Event code 1 (Y)
Value 2015
Min 0
Max 4095
Event code 24 (Pressure)
Value 0
Min 0
Max 1
Testing ... (interrupt to exit)
And when I touch it:
Event: time 43.599315, type 3 (Absolute), code 24 (Pressure), value 1
Event: time 43.639031, type 3 (Absolute), code 0 (X), value 2110
Event: time 43.639031, type 3 (Absolute), code 1 (Y), value 2857
Event: time 43.639063, -------------- Report Sync ------------
Event: time 43.682999, type 3 (Absolute), code 0 (X), value 2105
Event: time 43.683031, type 3 (Absolute), code 1 (Y), value 2851
Event: time 43.683031, type 3 (Absolute), code 24 (Pressure), value 0
Event: time 43.683031, -------------- Report Sync ------------
Event: time 44.163057, type 3 (Absolute), code 24 (Pressure), value 1
Event: time 44.203028, type 3 (Absolute), code 0 (X), value 3686
Event: time 44.203059, type 3 (Absolute), code 1 (Y), value 3326
Event: time 44.203059, -------------- Report Sync ------------
Event: time 44.243062, type 3 (Absolute), code 0 (X), value 3704
Event: time 44.243093, type 3 (Absolute), code 1 (Y), value 3281
Event: time 44.243093, -------------- Report Sync ------------
Event: time 44.287000, type 3 (Absolute), code 0 (X), value 3708
Event: time 44.287031, type 3 (Absolute), code 1 (Y), value 1939
Event: time 44.287031, type 3 (Absolute), code 24 (Pressure), value 0
Event: time 44.287031, -------------- Report Sync ------------
Что сделать, чтобы тач стал выводить изображение, похоже я что-то забыл?
-
Вот сам тач
http://clip2net.com/s/j5BNJ6
http://clip2net.com/s/j5BSl9
-
Подключил точно рабочий такой же тач, результат тот же
-
Добрый день.
Прикрепите полный лог загрузки Тиона.
-
PowerPrep start initialize power...
Battery Voltage = 0.32V
No battery or bad battery detected!!!.Disa
bling battery voltage measurements./r/nApr 24
201311:42:00
FRAC 0x92925552
memory type is DDR2
Wait for ddr ready 1power 0x00820616
Frac 0x92925552
start change cpu freq
hbus 0x00000003
cpu 0x00010001
start test memory accress
ddr2 0x40000000
finish simple test
U-Boot 2009.08 (Apr 24 2013 - 11:30:39)
Freescale i.MX28 family
CPU: 454 MHz
BUS: 151 MHz
EMI: 205 MHz
GPMI: 24 MHz
DRAM: 128 MB
MMC: IMX_SSP_MMC: 0, IMX_SSP_MMC: 1
In: serial
Out: serial
Err: serial
Net: got MAC address from IIM: 00:04:00:00:00:00
FEC0
Hit any key to stop autoboot: 0
MMC read: dev # 0, block # 256,count 12288 ...
12288 blocks read: OK
## Booting kernel from Legacy Image at 42000000 ...
Image Name: Linux-2.6.35.3-571-gcca29a0
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2484912 Bytes = 2.4 MB
Load Address: 40008000
Entry Point: 40008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.35.3-571-gcca29a0 (ubuntu@ubuntu) (gcc version 4.4.4 (4.4.4_09
.06.2010) ) #7 PREEMPT Wed Jun 26 10:41:28 EDT 2013
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: Freescale MX28EVK board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: console=ttyAM0,115200n8,video=mxs-fb:tag=VGA root=/dev/mmcb
lk0p3 rw rootwait
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 124476k/124476k available, 6596k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xfde00000 - 0xffe00000 ( 32 MB)
vmalloc : 0xc8800000 - 0xf0000000 ( 632 MB)
lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc0030000 ( 160 kB)
.text : 0xc0030000 - 0xc04d1000 (4740 kB)
.data : 0xc04d2000 - 0xc050e800 ( 242 kB)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:288
Console: colour dummy device 80x30
console [ttyAM0] enabled
Calibrating delay loop... 226.09 BogoMIPS (lpj=1130496)
pid_max: default: 32768 minimum: 301
Security Framework initialized
SELinux: Initializing.
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
regulator: vddd: 800 <--> 1575 mV at 1500 mV fast normal
regulator: vdddbo: 800 <--> 1575 mV fast normal
regulator: vdda: 1500 <--> 2275 mV at 1800 mV fast normal
vddio = 3380000, val=10
regulator: vddio: 2880 <--> 3680 mV at 3380 mV fast normal
regulator: overall_current: fast normal
regulator: vbus5v:
regulator: mxs-duart-1: fast normal
regulator: mxs-bl-1: fast normal
regulator: mxs-i2c-1: fast normal
regulator: mmc_ssp-1: fast normal
regulator: mmc_ssp-2: fast normal
regulator: charger-1: fast normal
regulator: power-test-1: fast normal
regulator: cpufreq-1: fast normal
i.MX IRAM pool: 120 KB@0xc8820000
Initializing GPMI pins
Initializing GPMI pins
usb DR wakeup device is registered
IMX usb wakeup probe
audit: cannot initialize inotify handle
bio: create slab <bio-0> at 0
SCSI subsystem initialized
Freescale USB OTG Driver loaded, $Revision: 1.55 $
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource mxs clock source
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Bus freq driver module loaded
IMX usb wakeup probe
usb h1 wakeup device is registered
mxs_cpu_init: cpufreq init finished
audit: initializing netlink socket (disabled)
type=2000 audit(0.600:1): initialized
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 243
alg: No test for stdrng (krng)
cryptodev: driver loaded.
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
get_max_memsize: mem_size now 614400
mxsfb_check_var: xres 640, yres 480, bpp 16
get_matching_pentry: 480:640:16 vs 480:640:16
get_matching_pentry: 480:640:16 vs 480:640:16
get_matching_pentry: 480:640:16 vs 480:640:16
mxsfb_pan_display: var->xoffset 0, info->var.xoffset 0
Console: switching to colour frame buffer device 80x30
mxsfb_pan_display: var->xoffset 0, info->var.xoffset 0
mxs-duart.0: ttyAM0 at MMIO 0x80074000 (irq = 47) is a DebugUART
UART set mode; UART - 0, mode - 0
mxs-auart.0: ttySP0 at MMIO 0x8006a000 (irq = 112) is a mxs-auart.0
Found APPUART 3.1.0
UART set mode; UART - 1, mode - 1
mxs-auart.1: ttySP1 at MMIO 0x8006c000 (irq = 113) is a mxs-auart.1
Found APPUART 3.1.0
UART set mode; UART - 2, mode - 2
mxs-auart.2: ttySP2 at MMIO 0x8006e000 (irq = 114) is a mxs-auart.2
Found APPUART 3.1.0
UART set mode; UART - 3, mode - 0
mxs-auart.3: ttySP3 at MMIO 0x80070000 (irq = 115) is a mxs-auart.3
Found APPUART 3.1.0
UART set mode; UART - 4, mode - 0
brd: module loaded
loop: module loaded
i.MX GPMI NFC
NFC: Version 1, 8-chip GPMI and BCH
Boot ROM: Version 1, Single-chip boot area, block mark swapping supported
Scanning for NAND Flash chips...
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit
)
-----------------------------
NAND Flash Device Information
-----------------------------
Manufacturer : Micron (0x2c)
Device Code : 0xda
Cell Technology : SLC
Chip Size : 256 MiB
Pages per Block : 64
Page Geometry : 2048+64
ECC Strength : 4 bits
ECC Size : 512 B
Data Setup Time : 20 ns
Data Hold Time : 10 ns
Address Setup Time: 20 ns
GPMI Sample Delay : 6 ns
tREA : Unknown
tRLOH : Unknown
tRHOH : Unknown
Description : MT29F2G08
-----------------
Physical Geometry
-----------------
Chip Count : 1
Page Data Size in Bytes: 2048 (0x800)
Page OOB Size in Bytes : 64
Block Size in Bytes : 131072 (0x20000)
Block Size in Pages : 64 (0x40)
Chip Size in Bytes : 268435456 (0x10000000)
Chip Size in Pages : 131072 (0x20000)
Chip Size in Blocks : 2048 (0x800)
Medium Size in Bytes : 268435456 (0x10000000)
------------
NFC Geometry
------------
ECC Algorithm : BCH
ECC Strength : 8
Page Size in Bytes : 2112
Metadata Size in Bytes : 10
ECC Chunk Size in Bytes: 512
ECC Chunk Count : 4
Payload Size in Bytes : 2048
Auxiliary Size in Bytes: 16
Auxiliary Status Offset: 12
Block Mark Byte Offset : 1999
Block Mark Bit Offset : 0
-----------------
Boot ROM Geometry
-----------------
Boot Area Count : 1
Boot Area Size in Bytes : 20971520 (0x1400000)
Stride Size in Pages : 64
Search Area Stride Exponent: 2
Scanning device for bad blocks
Boot area protection is enabled.
Creating 2 MTD partitions on "gpmi-nfc-main":
0x000000000000-0x000001400000 : "gpmi-nfc-0-boot"
0x000001400000-0x000010000000 : "gpmi-nfc-general-use"
mxs-spi mxs-spi.0: Max possible speed 24000 = 24000000/2 kHz
mxs-spi mxs-spi.0: at 0x80014000 mapped to 0xF0014000, irq=84, bus 1, DMA ver_ma
jor 4
Freescale FlexCAN Driver
FEC Ethernet Driver
fec_enet_mii_bus: probed
Register PTP device as char /dev/ptp
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
fsl-ehci fsl-ehci: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci: irq 92, io base 0x80090000
fsl-ehci fsl-ehci: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
ARC USBOTG Device Controller driver (1 August 2005)
mice: PS/2 mouse device common for all mice
input: MXS touchscreen as /devices/virtual/input/input0
rtc-ds1307 0-0068: rtc core: registered m41t00 as rtc0
i2c /dev entries driver
IR NEC protocol handler initialized
IR RC5(x) protocol handler initialized
IR RC6 protocol handler initialized
IR JVC protocol handler initialized
IR Sony protocol handler initialized
Linux video capture interface: v2.00
WARNING : No battery connected !
Aborting power driver initialization
mxs-battery: probe of mxs-battery.0 failed with error 1
mxs watchdog: initialized, heartbeat 19 sec
mxs-mmc: MXS SSP Controller MMC Interface driver
mxs-mmc mxs-mmc.0: mmc0: MXS SSP MMC DMAIRQ 82 ERRIRQ 96
dcp dcp.0: DCP crypto enabled.!
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
can: controller area network core (rev 20090105 abi 8)
NET: Registered protocol family 29
mmc0: new high speed SDHC card at address 59b4
mmcblk0: mmc0:59b4 USD 14.7 GiB
mmcblk0: p1 p2 p3
regulator_init_complete: incomplete constraints, leaving vbus5v on
rtc-ds1307 0-0068: setting system clock to 2001-08-27 01:51:38 UTC (998877098)
VFS: Mounted root (ext2 filesystem) on device 179:3.
Freeing init memory: 160K
init started: BusyBox v1.15.0 ()
starting pid 1101, tty '': '/etc/rc.d/rcS'
Mounting /proc and /sys
Starting the hotplug events dispatcher udevd
Synthesizing initial hotplug events
Setting the hostname to freescale
Mounting filesystems
mount: sysfs already mounted or /sys busy
mount: according to mtab, /sys is already mounted on /sys
mount: mount point /proc/bus/usb does not exist
Starting inetd:
Starting the port mapper:
Starting the dropbear ssh server:
starting pid 2132, tty '': '/sbin/getty -L ttyAM0 115200 vt100'
arm-none-linux-gnueabi-gcc (4.4.4_09.06.2010) 4.4.4
root filesystem built on Wed, 03 Jul 2013 08:12:34 -0400
Freescale Semiconductor, Inc.
-
в bootargs пробовал передавать
console=ttyAM0,115200n8,video=mxs-fb:tag=3.5
console=ttyAM0,115200n8,video=mxs-fb:tag=5.7
console=ttyAM0,115200n8,video=mxs-fb:tag=VGA
-
Образ наш или свой собирали?
-
В общем то да, в этом и была проблема) Буквально только что вот скачал образ ядра, которые вы говорили, закинул в boot оба файла uImage и imx28_ivt_linux.sb, запустил, и всё заработало! До этого образ был, который в виртуалке был. Большое спасибо за помошь!!